Waardering:
  • 0 stemmen - gemiddelde waardering is 0
  • 1
  • 2
  • 3
  • 4
  • 5
De instelling 3 fase meter
#1
Good evening; sorry to post this in English, but my Dutch is too rusted to write clearly; I am a new Beeclear user in Belgium / Wallonia, and have got the same problem as described: no Elektriciteit Actueel display, as the date on top of the chart displays 1970. I had to set the parameter '3 phases' to UIT to have a display. The problem is that I have a 3 phases smartmeter!
The info display is following:

Software versie                             49.10_BE
Regio                                            BE
Hardware versie                            2
DSMR protocol versie                   50214

meter type                                   FLU5\253769484_A
Serie nummer elektriciteit meter    1SAG3100121400

uptime                                         8 dagen
tijd bron                                      ntp

P1-signaal                                    Ok
SD-kaart aanwezig                       Ok
SD-kaart grootte                         15.47 GB
SD-kaart vrije ruimte                   100.0%


Is it normal?? Please explain...
Dank u wel in vooraad
Antwoord
#2
Het presenteren van drie fase metingen voor de (actueel) lijngrafiek is voor de Belgische slimme meters (nog) niet geïmplementeerd.

Hoofdoorzaak is dat de resolutie (fijnmazigheid) van de meting in België (Fluvius) te grof is, waardoor een dergelijke meting 
weinig zinvol is om te presenteren (dit was de toestand op 1.1.2020). We wachten totdat de Belgische netbeheerder(s) een verbetering hier in zullen aanbrengen. 

Nu is de functie "3 fase meter" hierdoor niet operationeel.
Antwoord
#3
(06-11-2020, 19:12 PM)Patrick K schreef: Good evening; sorry to post this in English, but my Dutch is too rusted to write clearly; I am a new Beeclear user in Belgium / Wallonia, and have got the same problem as described: no Elektriciteit Actueel display, as the date on top of the chart displays 1970. I had to set the parameter '3 phases' to UIT to have a display. The problem is that I have a 3 phases smartmeter!
The info display is following:

Software versie                             49.10_BE
Regio                                            BE
Hardware versie                            2
DSMR protocol versie                   50214

meter type                                   FLU5\253769484_A
Serie nummer elektriciteit meter    1SAG3100121400

uptime                                         8 dagen
tijd bron                                      ntp

P1-signaal                                    Ok
SD-kaart aanwezig                       Ok
SD-kaart grootte                         15.47 GB
SD-kaart vrije ruimte                   100.0%


Is it normal?? Please explain...
Dank u wel in vooraad

Dear Patrick K,

Can you generate a so called debug.log for us? 

You can find instructions how to generate a debug_info.log at page 31 of the manual (see attachement).

Please mail the debu_info.tar.gz file to: info@beeclear.nl

Regards,

Your2Power - BeeClear


Bijlagen
.pdf   Manual_BeeClear_EN_v002.pdf (Grootte: 1,95 MB / Aantal keer gedownload: 1.241)
Antwoord
#4
Thumbs Up 
Hello,

FYI found out that ORES, the metering company / operator in south Belgium (Wallonia) implemented the DSMR protocol  version V5.0.2.15 in March 2021 and now sends the instantaneous active power delivered  and injected on each phase (21.7.0 / 41.7.0 / 61.7.0 / 22.7.0 / 42.7.0 / 62.7.0). Therefore the parameter '3 fase') can be set and the values are displayed correctly! see capture attached

v/r, Patrick


Bijlagen Afbeeldingen
   
Antwoord
#5
Hallo,
Enkele dagen heb ik de beeclear aangesloten op mijn slimme meter.
We hebben 3x220V aansluitting
Nu kan ik de tweede fase niet zien? Geen verbruik en teruglevering.
Enig idee hoe ik dit kan oplossen?

Alvast bedankt
   
Antwoord


Ga naar locatie: